Volume 7, Issue 3, September 2018, Page: 67-72
Experimental and FEM Simulation Analysis of Lateral Extrusion Process on Bimetal Cross Fitting
Le Thai Hung, School of Material Science and Engineering, Hanoi University of Science and Technology, Hanoi, Vietnam
Do Quang Long, School of Material Science and Engineering, Hanoi University of Science and Technology, Hanoi, Vietnam
Le Trung Kien, School of Mechanical Engineering, Hanoi University of Science and Technology, Hanoi, Vietnam
Vu Xuan Hung, School of Material Science and Engineering, Hanoi University of Science and Technology, Hanoi, Vietnam
Pham Quang, School of Material Science and Engineering, Hanoi University of Science and Technology, Hanoi, Vietnam
Received: Jun. 17, 2018;       Accepted: Jul. 9, 2018;       Published: Aug. 15, 2018
DOI: 10.11648/j.am.20180703.12      View  548      Downloads  52
Abstract
The purpose of this paper is to study combines the finite element method model and experimental on bimetal cross fitting by lateral extrusion process. Fabricating bimetallic cross fitting by lateral extrusion technique remains some difficulties like taking the product out of the die hardly, harming the die longevity since the high compressive force and friction effects. The Finite Element Method (FEM) results of bimetal cross fitting lateral extrusion process were obtained from ABAQUS software such as: Stress distribution, metal flow and influence of sleeve thickness. Numerical results were compared with the experimental results shown a good agreement. The bimetal cross fitting has been successfully fabricated by lateral extrusion process. The results showed a close agreement between the numerical simulation and experimental analysis of bimetal cross fitting.
Keywords
Bimetal, Cross Fitting, Lateral Extrusion, FEM
To cite this article
Le Thai Hung, Do Quang Long, Le Trung Kien, Vu Xuan Hung, Pham Quang, Experimental and FEM Simulation Analysis of Lateral Extrusion Process on Bimetal Cross Fitting, Advances in Materials. Vol. 7, No. 3, 2018, pp. 67-72. doi: 10.11648/j.am.20180703.12
Copyright
Copyright © 2018 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
T. Altan, “Lateral extrusion Solid forming, Metal Forming Handbook”, Schuler (c) Springer-Verlag Berlin Heidelberg (1998).
[2]
U. C. Paltasingh, S. K. Sahoo, P. Dash, K. C. Nayak,“Simulation and experimental studies for lateral extrusion of square and pentagonal head from round shaft”, International Journal of Research in Engineering and Technology. (2013) pp. 2319-1163.
[3]
M. Zadshakoyan, H. Jafarzadeh, E. A. Sobbouhi, “Injection forging of splines using numerical and experimental study”, International Journal of Aerospace and Mechanical Engineering 4, (2010) pp. 179-184.
[4]
H. Jafarzadeh, M. Zadshakoyan, “Numerical and experimental studies of splines produced by injection forging process”, Materials and Manufacturing Processes 26 (5), (2011) pp. 703-712.
[5]
M. Zadshakoyan, E. A. Sobbouhi, H. Jafarzadeh, “Investigation of precision forging process of spur gears: Numerical analysis and experiments”, Advanced Materials Research 341, (2012) pp. 265-270.
[6]
M. Zadshakoyan, H. Jafarzadeh, E. Abdi Sobbouhi, “Injection Forging of Splines Using Numerical and Experimental Study”, Engineering and Technology International Journal of Industrial and Manufacturing Engineering Vol:3, No:4, (2009) pp. 422-427.
[7]
M. Zadshakoyan and H. Jafarzadeh, “Numerical Study of the Die Geometry and Friction Effect on the Forming Load and Material Flow in Injection Forging Process”. Journal of Applied Sciences, 9 (2009) pp. 2174-2179.
[8]
H. Jafarzadeh, G. Faraji and A. F. Dizaji, “Analysis of lateral extrusion of gear-like form parts,” Journal of Mechanical Science and Technology 26 (2012) pp. 3243-3252
[9]
U. C. Paltasingh, S. K. Sahoo, P. R. Das, K. C. Nayak, S. Potnuru, “Lateral Extrusion of Spur gears with Involute Profile: Finite Element Analysis and Experimental Investigation”, IOSR Journal of Engineering (IOSRJEN), Vol. 3, Issue 7 (2013) pp. 20-30.
[10]
U. C Paltasingh, S. K. Sahoo, P. R. Dash, K. C. Nayak, S. Potnuru, “FEM Analysis And Experimental Investigation For Lateral Extrusion Of Hexagonal Head”, International Journal of Engineering Research and Applications (IJERA), Vol. 3, Issue 4, (2013), pp. 1265-1271.
[11]
M. Plančak, M. Rosochowska, P. Skakun, “Radial extrusion of gear like components – numerical analysis and experiment”, Technical Gazette 20, 5(2013), pp. 891-896.
[12]
I. Kačmarčik, M. Plančak, D. Vilotić, M. Tolnai, D. Movrin, A. Ivanišević, “Numerical analysis of bi-metallic extrusion of gear-like components”, The 6th PSU- UNS International Conference on Engineering and Technology, ICET2013 T. 10-1. 3, (2013) pp. 1-4.
[13]
O. C. Zienkiewicz and R. L. Taylor, “The Finite Element Method (Vol. 2: Solid Mechanics),” Published by Butterworth-Heinemenn (2000).
[14]
E. A. Brandes, “Smithells metals reference book”, Butterworths, (1988).
[15]
A. S. Scari, B. C. Pockszevnicki, J. L. Junior and P. A. A. M. Junior, “Stress-Strain Compression of AA6082-T6 Aluminum Alloy at Room Temperature”, Journal of Structures Volume (2014), Article ID 387680, 7 pages.
[16]
Abaqus 6. 13: Abaqus/CAE User´`s Manual.
Browse journals by subject